[ Home ] [ Up ] [ LinAire Products Page ] [ Services ] [ Distributors ] [ Harness Use List ] [ Feedback ] [ Literature Request ][ Search Page ]
[ Picture Gallery ]

Updates

 

  

 

 

 

[ Home ] [ Up ] [ LinAire Products Page ] [ Services ] [ Distributors ] [ Harness Use List ] [ Feedback ] [ Literature Request ]

 

Table of Contents

CONTACT
  INFORMATION:
  LinAire Engineering 
                                                       LinAire 
DISTRIBUTORS

  Search Web Site

 

March 2001

                        It has been discovered that the LXS 4 SDI switch maybe wired wrong.  The bare wire jumper on the switch should look like the picture below, however, this jumper maybe wired one switch position clockwise from its correct location.  This mistake will cause the wrong transponder side to identified as follows:  ALL CALL position will ID the transponder as XPNDR #1 and the XPNDR #1 position as XPNDR#2 and the XPNDR#3 as ALL CALL.

                        If you find this to be the case please rewire the jumper on the switch as in the picture below.

 

 Click on picture to enlarge.

 

P4-20     P4-21    SDI
open      open     ALL CALL
open       gnd      XPNDR #1
gnd       open      XPNDR #2
gnd         gnd      XPNDR #3           

 

ON / STBY Switch should have a Black with White wire connected to the top terminal of the switch.

                                                                                                      ON                    Panel top^

                         LXS 4 panel  P4-24 Black/white      -------------O
                                                                                                        O---------------     Ground line
                                                                                                         O                                

                                                                                                    STBY

 

April 2000

From: Linaire Engineering
            Design Department

Subject: Panel Lights Primus 200 radar system harnesses.

LW7011 Linaire harness modification for the addition of Panel Lamps require the following changes to the harness.

Parts Required:             6 feet of Belden cable   8489

 

Follow the pin to pin list to add this cable into the LW 7011 harness.

First wire P-101 Mono ( KPTO 6 B 18-32S) on the radar units harness end.

Second tyrap the new cable along the LW7011 harness IND cable.

Third open the LW7011 IND (DPX 57 34P) connector, trim cable and wire as listed.

 

P-101 Mono Connector Wire LW7011 IND

PIN                             Color                             PIN

c        5 VAC/ DC     White                             47 and 49

f         27.5 VDC        Red                                19

h        Common        Black                             56 and 57

April 2000

From: Linaire Engineering
            Design Department

Subject: Panel Lights Primus 800 radar system harnesses.

LW7014 Linaire harness modification for the addition of Panel Lamps require the following changes to the harness.

Parts Required:     12 feet of Belden cable 8489
                                   1 Each DPX 57 34P connector
                                  1 Each DPX 22017 connector hood

Follow the pin to pin list to add this cable into the LW 7014 harness.

First, wire J-101 IND ( KPTO 6 B 18-32S) on the radar units harness end.

Second, tyrap the new cable along the LW7014 RT harness cable and then break away from the LW7014 RT at the panel end. You need to leave enough cable to allow the new IND connector to plug into the LW panel IND connector.

Third, wire the new DPX 57 34P connector as listed and mark it LW7014 IND.

J-101 IND Connector                         Wire                     LW7014 IND
PIN                                                      Color                     PIN

T         5 VAC/ DC                             White                     47 and 49

S         27.5 VDC                                 Red                        19

A         Common                                 Black                     56 and 57

 

UP DATE HARNESS USE LIST

SEPTEMBER 1999 --  The LX9106 for the KING KT70 transponder also runs the KT71 transponder.

  Avionics Test Equipment Panels and Cables for bench testing of Aircraft Radio, Navigation, Audio Controllers, Radar and more. Linaire Engineering Inc.
Last modified: June 15, 2004